The main technical parameters: Model Input power frequency Total power maximum operating speed of minimum glass size glass size glass thickness dimensions BXWJ-1200 380v 50hz 12kw 0-4m/min 100 * 200mm 1200 * 2500mm 3-8mm 2500 * 1600 * 900mm BXWJ-800 380v 50hz 12kw 0-4m/min 50 * 100mm 800 * 2000mm 3-8mm 2100 * 1200 * 900mm small glass washing and drying machines This product is suitable for cleaning 3-8mm thick plate glass. The machine adopts horizontal level institutions. Step: the feed section, the pressure roller cleaning section, the drying section and the discharge section. The whole machine adopts variable frequency motor speed. The machine easy to operate, economical and practical. Glass Cleaner Glass Cleaner small craft ultrasonic cleaning (according to the technical requirements set multiple processes) - rinsing - drying - the material Note: glass washing machine as well as the sub-vertical and horizontal, vertical smaller footprint high efficiency, high degree of automation, an area slightly larger horizontal, require manual, low efficiency. One uses for the washing of the thickness of 3 ~ 19MM glass. Small glass washing and drying machine adopts horizontal structure level, flat glass placed on the transfer roller, through the feed section (1), cleaning section (2), drying section (3), to reach the feed section (4). Glass transmission speed according to the relevant technical requirements, AC Motor, the air temperature can also be set in advance needed. The machine is easy to operate, the operation buttons focused on the operating table. Note (1) must pay attention to the first open air blower, heater after opening. First off the heater, the blower off. (2) When changing the thickness of the glass, be sure to adjust the level of the position of the upper hand knife, or will cause damage accident. (3) before stopping transmission motor speed regulator must take down to zero. (4) with emergency stop button on the console, the event of an emergency, can be used. (5) the glass must be placed in the feed section within the limit range. (6) when added to the wash water tank, the water level should not exceed 250MM, 200MM to promptly when the water level is below water. Small glass washing and drying machines for routine maintenance and care is a very important thing, usually moving parts of the machine should always observe the waterway system, air duct systems, electrical systems, in case of emergency immediately stop checks. (1) lubrication of bearings and lubrication for each point in time for lubrication. Maintenance cleaning section (2) of the waterway system circulating water is used. Every day the water in the tank should be replaced to ensure clean water for washing, cleaning once a month tanks and filters. Through the observation hole cleaning section cover spray can monitor the situation, if we find there is clogging, then stop the pump open the lid, remove the spray nozzle, drain cleaning after installation. Maintenance (3) shunt system regularly check the operation of the blower, stop immediately in case of an abnormal sound, the maintenance department inspection reports. Each month the filter inlet gate for cleaning, usually to keep the small glass washing and drying machine blower house cleaning to prevent dust is inhaled air duct, glass contamination. (4) water systems waterway system shown in Figure 3, the four sets of two tanks of circulating water system. The detergent tank is appropriate PH = 7 neutral glass cleaners, glass last rinse of deionized water is preferred, a direct impact on the water quality of the glass surface cleanliness. The temperature of the washing liquid is generally controlled at 30 to 60 degrees (water heating control device users themselves). (5) air duct system is shown in Figure 4, the compressed air from the blower out of the wind respectively given by the upper and lower knives and the cold wind, the distance between the plane and the glass under hot knife can be adjusted when changes in the thickness of the glass , must pay attention to adjust this gap. (6) Installation and adjustment ① field conditions should have 380V AC power supply, industrial water supply source, drain. ② shown in Figure 7, the right display rack feeding section, a cleaning section rack, the rack drying section, the feed section of the rack cabinet and ventilated cabinets.